Ingeniería de Sonido · 2019
Ubicación estratégica de material absorbente basado en el análisis modal de una sala
This grade work was carried out in order to test the hypothesis that the location of the absorbent material at the absolute sound pressure maxima of a room decreases the reverberation time in the octave band to which the mode frequency belongs. The results obtained in the reverberation time T_15 and T_20 of a room in the 125 Hz octave band are presented, in which, by means of a modal analysis, the location of the absorbent material was varied in order to obtain the maximum absorption of sound energy. For its implementation it was necessary to carry out a survey of a 3D model of the room and import it into a finite element simulation software, with which the absolute maximum and minimum sound pressure was determined. A simulation was then carried out in the CATT-Acoustics v9.1 software, in which two panel configurations were tested, one in which the absorbent material was placed at absolute maximum pressure and the other at minimum pressure. After the simulation, a measurement based on an experimental design was performed. The measurement involved 18 combinations of source location, microphones and absorber panel configuration, after which the responses to the impulse of each combination were found by means of the MATLAB software and the reverberation time for each measurement point was estimated consecutively by means of the plug-in aurora software Audacity 2.0.5. Finally, a statistical analysis was performed to determine the factors that were statistically significant in the measurement results.
Texto completo 55 páginas con texto
Leer la tesis completa Ficha en el repositorio
Contenido
- RESUMENp. 7
- ABSTRACTp. 8
- I. INTRODUCCIÓNp. 9
- II. PLANTEAMIENTO DEL PROBLEMAp. 10
- III. JUSTIFICACIÓNp. 11
- IV. OBJETIVOSp. 12
- A. Objetivo generalp. 12
- B. Objetivos específicosp. 12
- V. ESTADO DEL ARTEp. 13
- VI. MARCO TEÓRICOp. 15
- Modos propios de una salap. 15
- Clasificación de los modos propiosp. 18
- Método de elementos finitosp. 19
- Estudio de convergencia de mallap. 20
- Acústica geométricap. 21
- Reverberaciónp. 21
- Tiempo de reverberaciónp. 21
- Medición del tiempo de reverberaciónp. 23
- Respuesta al impulso y procesamiento digital de señalesp. 23
- Delta de Diracp. 23
- Respuesta al impulsop. 24
- Convoluciónp. 24
- Transformación de Fourierp. 25
- Diseño y análisis de experimentosp. 25
- Definiciónp. 25
- Diseño factorial completo y fraccionadop. 26
- Análisis modalp. 29
- Diseño de experimentop. 28
- Implementaciónp. 29
- Análisis modalp. 29
- Simulaciónp. 35
- Mediciónp. 36
- VIII. RESULTADOSp. 39
- Simulaciónp. 35
- Mediciónp. 36
- Análisis estadísticop. 40
- Gráficos de intervalosp. 41
- IX. CONCLUSIONESp. 44
- REFERENCIASp. 45
- ANEXOSp. 47
- TABLA I. ORDEN DE LAS MEDICIONESp. 28
- TABLA II. CANTIDAD DE MATERIAL EN M2p. 30
- LA MALLAp. 32
- TABLA IV. ÁREAS MATERIALES DEL AULAp. 36
- TABLA V. COEFICIENTES DE ABSORCIÓN BLACK THEATER DE 2”p. 36
- TABLA VI. COORDENADAS DE POSICIONES DE LAS FUENTES Y MICRÓFONOSp. 38
- DE 125 HZp. 39
- MICRÓFONO Y CONFIGURACIÓN DE PANELESp. 39
- TABLA IX. RESULTADOS ANÁLISIS ANOVA PARA 𝑇15 Y 𝑇20p. 41
- Fig. 1. Distribución Niveles SPL normalizados asociados a un modo propio de la salap. 15
- Fig. 2. Tipos de modos de vibraciónp. 18
- Fig. 3. Interior del recintop. 30
- Fig. 5. Modelo importado al software de simulación de elementos finitosp. 31
- Fig. 6. Ubicación de máximos y mínimos puntos de presión en la frecuencia de 125 Hzp. 33
- Fig. 7. Configuración de paneles en los máximos (arriba) y mínimos de presión (abajo)p. 34
- máximos absolutos de presión (derecha)p. 35
- Fig. 9. Panel implementado en la mediciónp. 37
- Fig. 10. Ubicación de fuentes y micrófonosp. 37
- micrófono 1p. 38
- Fig. 12. Gráfico de intervalo de confianza para las dos configuraciones de paneles de T15p. 42
- Fig. 13. Gráfico de intervalo de confianza para las dos configuraciones de paneles de T20p. 43