Medellín - Minas - Doctorado en Ingeniería - Sistemas Energéticos · 2023
Numerical modeling of massive sand production during cold heavy oil production
Cold heavy oil production with sand (CHOPS) is a single well technology that involves the deliberate initiation and sustaining of sand inflow into the wells using progressive cavity pumps (PCP) to produce at oil high rates with a subsequent high-pressure drawdown around the wellbore and improvement in oil well productivity. CHOPS is a primary recovery method extensively used in the world as a profitable and simple technology. Foamy-oil flow and wormhole formation are the main mechanisms of CHOPS, where aggressive sand production is a consequence of geomechanical issues such as elastoplastic behavior, stress redistribution, failure criteria, pressure gradient, erosion, and sand liquefaction. The general objective of this thesis is to build a numerical model to predict and explain massive sand production during cold heavy oil production by coupling fluid flow with geomechanics and considering stress redistribution and erosional processes. This research also identifies the relevant phenomena of massive sand production and describes the interaction between geomechanical and erosional processes. A methodology is proposed to model the initiation and propagation of wormholes based on geomechanical behavior. A 3D-single well model is built to understand the cold heavy oil production with sand, considering relevant dynamics such as stress redistribution and the interaction between geomechanical and erosional processes, by coupling fluid flow with geomechanics. This model couples a three-phase fluid flow model and an elastoplastic model and integrates other models: a sand production model, a foamy-oil module, and a conceptual model for wormhole formation. This coupled model is verified and validated firstly by components and lately integrating step by step the different components using commercial software such as ABAQUS® and CMG®. Field cases are run to calibrate the parameters of the sand production model resulting in low sand levels, a case with the main characteristics of a CHOPS well is run and its results are analyzed, and a sensitive study is performed to evaluate the impact of variables such as pressure drawdown, cohesion, internal friction angle, and stress regime. Finally, a special case is built combing all variables and looking to promote sand production with successful results.
Full text 295 pages with text out of 307
Read the full thesis Record in the repository
Contents
- Abstractp. 9
- Nomenclaturep. 18
- Chapter 1. Introductionp. 23
- Overviewp. 23
- Problem statementp. 23
- Backgroundp. 24
- Objectivesp. 26
- General objectivep. 26
- Specific objectivesp. 26
- Outlinep. 26
- Chapter 2. State of the artp. 27
- Basics of cold heavy oil production with sand – CHOPSp. 27
- Mechanisms of cold production with sandp. 29
- Foamy oilp. 20
- Wormholes formationp. 32
- State of the artp. 35
- Sand productionp. 37
- Foamy oilp. 20
- Wormholes formationp. 32
- Elastoplasticityp. 48
- Chapter 3. General Modelp. 51
- Physical modelp. 51
- Fluid flow modelp. 52
- Fluid mass conservationp. 52
- Solid mass conservationp. 53
- Darcy’s lawp. 53
- Equation of statep. 55
- Compressibility of the formationp. 55
- Other relationsp. 56
- Governing equationsp. 57
- Boundary conditionsp. 59
- Initial conditionsp. 62
- Ternary model for the three-phase systemp. 63
- Geomechanical modelp. 66
- Basic relationsp. 67
- Elasticityp. 69
- Elastoplasticityp. 48
- Computer modelp. 79
- Chapter 4. CHOPS modelp. 83
- Foamy-oil modelp. 83
- Phases and Componentsp. 85
- Premises and assumptionsp. 86
- Conceptual parametersp. 86
- Inflow performancep. 87
- Relative permeabilityp. 91
- Module implementationp. 92
- Sand production modelp. 93
- Sanding onsetp. 94
- Sand production criterionp. 94
- Equivalent plastic strain calculationp. 96
- Module implementationp. 92
- Wormholes methodologyp. 98
- Module implementationp. 92
- Chapter 5. Model Validationp. 103
- Fluid flow modelp. 52
- One-phase modelp. 104
- Two-phase modelp. 109
- Three-phase casep. 111
- Geomechanical modelp. 66
- Elastic modelp. 112
- Elastoplastic modelp. 97
- Coupled modelp. 135
- Two-phase and elastic casep. 135
- Two-phase and elastoplastic casep. 143
- Chapter 6. Resultsp. 153
- Foamy-oil analysisp. 153
- Effect of foamy oil on fluid propertiesp. 153
- Effect of foamy oil on relative permeabilityp. 158
- Effect of foamy oil inflow performancep. 159
- Data analysis of field data for sand productionp. 159
- Production performancep. 159
- Reservoir characteristicsp. 104
- Oil production and sand productionp. 170
- Sand production on productivityp. 171
- Simulation of sand production using the field datap. 171
- Simulation of a typical CHOPS wellp. 183
- Chapter 7. Conclusions and Recommendationsp. 195
- Conclusionsp. 195
- Recommendationsp. 199
- Annex A. Fluid flow modelp. 201
- Mathematical modelp. 201
- Fluid mass conservationp. 52
- A1.1.1. Oil-phasep. 202
- A1.1.2. Water-phasep. 203
- A1.1.3. Gas-phasep. 203
- Solid mass conservationp. 53
- Darcy’s lawp. 53
- A1.3.1. Oil phasep. 207
- A1.3.2. Water-phasep. 207
- A1.3.3. Gas-phasep. 208
- Equation of state (isothermal fluid compressibility)p. 208
- A1.4.1. Oil-phasep. 209
- A1.4.2. Water-phasep. 209
- A1.4.3. Gas-phasep. 209
- Compressibility of the formationp. 55
- Other relationsp. 56
- A1.6.1. Saturationsp. 210
- A1.6.2. Capillary pressuresp. 210
- Governing equationsp. 57
- A1.7.1. Oil-phasep. 211
- A1.7.2. Water-phasep. 214
- A1.7.3. Gas-phasep. 217
- Numerical modelp. 113
- Simulation gridp. 221
- Governing equations of the fluid flowp. 223
- A2.2.1. Oil-phasep. 223
- A2.2.2. Water-phasep. 228
- A2.2.3. Gas-phasep. 233
- Boundary conditionsp. 59
- A2.3.1. Radial directionp. 241
- A2.3.2. Tangential directionp. 243
- A2.3.3. Vertical directionp. 244
- Other relationsp. 56
- A2.3.1. Porosity equationp. 245
- A2.3.2. Variation of permeability with porosityp. 248
- A2.3.3. Transmissibility factorsp. 249
- Annex B. Implementation of Finite Element Method (FEM)p. 257
- Introductionp. 255
- Discretization of the domainp. 255
- Mesh generationp. 256
- Element characteristicsp. 256
- Variational formulationp. 257
- Strong formp. 258
- Weak formp. 259
- Discrete formulationp. 262
- The basic functionsp. 263
- The shape functionsp. 264
- Integrationp. 267
- Multi-layer modelp. 268
- Visco-plastic methodp. 269
- Implementation of the method to the elasto-plastic modelp. 271
- Explicit integration with the visco-plastic methodp. 273
- Convergencep. 274
- Annex C. PVT properties for heavy oilp. 275
- Gasp. 275
- General relationp. 275
- Gas deviation factorp. 275
- Corrected gas gravityp. 277
- Gas formation-volume factorp. 277
- Isothermal gas compressibilityp. 278
- Gas densityp. 278
- Gas viscosityp. 279
- Oilp. 304
- Oil gravityp. 280
- API gravityp. 280
- Characterization factorp. 280
- Molecular weightp. 18
- Bubble-point pressurep. 280
- Solution gas-oil ratiop. 280
- Oil formation-volume factorp. 284
- C2.7.1. Under-saturated oilp. 284
- C2.7.2. Gas-saturated oilp. 284
- Isothermal oil compressibilityp. 285
- C2.8.1 .Under-saturated oilp. 286
- C2.8.2. Gas-saturated oilp. 286
- Oil densityp. 287
- C2.9.1. Under-saturated oilp. 287
- C2.9.2. Gas-saturated oilp. 288
- C2.10. Oil viscosityp. 288
- C2.10.1. Dead-oil viscosityp. 288
- C2.10.2. Under-saturated oilp. 289
- C2.10.3. Gas-saturated oilp. 289
- Waterp. 290
- Water specific gravityp. 291
- Solution gas-water ratiop. 291
- Isothermal water compressibilityp. 291
- C3.3.1. Under-saturated waterp. 291
- C3.3.2. Gas-saturated waterp. 292
- Water formation-volume factorp. 292
- C3.4.1. Under-saturated waterp. 293
- C3.4.2. Gas-saturated waterp. 293
- Water viscosityp. 293
- Water densityp. 294
- Referencesp. 295